Some Help for Understanding Guide Numbers?
Posted 27 October 2012 - 12:01 PM
How is the brightness difference measured between different guide numbers. For example, how much brighter is GN24 than GN 20. Same question between GN 20 and GN 32 or 34? What about GN 40? Is GN 40 twice as bright (one stop?) or even brighter than GN 20. Let's assume, for now, the same angle of coverage to keep it simple.
Thanks for any help!
Posted 27 October 2012 - 12:57 PM
A strobe w/GN of 40 would reach twice as far as one that is 20. Power wise, the strobe with GN of 40 would actually be 4x as powerful since at 40 m away, the light is 4x weaker given it has spread to an area 4x greater.
For UW use, it is not quite the same, since the returning light of the strobe from the subject would also become bluer the farther away it is. So a strobe with GN of 20 could light something properly 10m away when using f/1 and ISO 100, and another strobe with GN of 30 would do so for subject 15m away. In acdtual use, it would be even less since you are also competing with ambient light.
Posted 27 October 2012 - 02:00 PM
Thanks for the response!
Posted 27 October 2012 - 02:05 PM
Edited by Lwang, 27 October 2012 - 02:08 PM.
Posted 27 October 2012 - 02:06 PM
The guide number formula is simple, GN=fstop x distance (meters), but you need to be careful, sometimes GN are given in air (mostly) and sometimes in water and sometimes in meters (mostly) and sometimes in feet.
Let's take the new S&S D1 as an example. It has a GN of 24 (with the diffuser that everyone uses) in air and an UW GN of about 12 (depends on clarity of the water obviously). A GN of 12 means that for a shot at 1 meter from the subject you can use F12 or to use f22 you need to be about half a meter away (.54 meters or 21 inches or so), if the water is quite clear. YMMV in the real world that isn't the NASA pool. In any case, take the GN of the strobes with some salt, since measuring them is not at all trivial.
Canon 7d, 50D, Nauticam,Subal, Inon Ringflash, Athena Ringflash, Inon z240 etc.
Posted 28 October 2012 - 07:11 AM
I use a two strobe set-up and thus would have 4 YS-01s (one pair on each side).
According to the above, the YS-01s will give a GN of 28 (each pair) at 100 degrees. I have tried this with two (to make a single strobe), and they are very bright and the recycle seems almost instant even shooting at night and at f16, with a 14mm lens about 15' from the test wall (my garage door). It does, as expected, seem about twice as bright (one stop) as a single ys-01.
Of course, you have to deal with two strobes, two sets of batteries and it is larger than the YS-D1 but surprisingly it is not at all unmanageable.
Against these disadvantages there is always redundancy in my dual strobe setup if one strobe fails, where if I have only 2 ys-D1s then I am down to one strobe. Also, for shooting macro, I can just use single strobes for getting into tight places.
I can get two used YS-01s for about $600. A single new YS-D1 costs about 700.
Posted 28 October 2012 - 01:58 PM
Alternatively, you can use a white card on the opposite side of the strobe to bounce some light back to the shadow side, but you can't carry a giant white board when the subject is a little farther away.
If you want to light up subject 5 ft away in situations where there is alot of ambient light, then the YS-D1 w/o the diffuser has much more power than even 2 YS-01 and produce better result.
The YS-D1 has better TTL and slave TTL, which is not avail in the YS-01.
Posted 28 October 2012 - 02:09 PM
Edited by guyharrisonphoto, 28 October 2012 - 02:11 PM.
Posted 28 October 2012 - 02:19 PM
4 YS-01 would have GN of 40, much more power than 1 YS-D1. If you use a pair of YS-D1, then its GN would be 45 (at 80 deg coverage). You definitely will have less batteries, arms fiber optic cables, etc to work with.